Physics | Physics homework help

 

 

 

1.                  What is the reading on the following Vernier? What is its resolution?

 

2.                  What is the reading on the following micrometer? What is its resolution?

 

 

 

3.                  A Vernier caliper subdivides the smallest division on the main scale into 100 equal parts. If each subdivision on the Vernier plate equals 0.001 in, what is the length of the smallest subdivision on the main scale?

 

a)      100*0.001 mm      b) 100 mm       c) 0.1 mm        d) a and c        e) None of the above

 

4.                  A micrometer subdivides the smallest division on the main scale into 50 equal parts. If each subdivision on the thimble equals 0.001 in, what is the length of the smallest subdivision on the main scale?

 

a)      100*0.001 mm      b) 0.001 in       c) 50 equal parts          d) None of the above

 

5.                  (SI units) A GO/NO-GO plug gage will be designed to inspect a 50.00 ± 0.20 mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gage. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage.

 

 

6.                  (SI units) A GO/NO-GO ring gage is needed to inspect the diameter of a shaft that is 50.00 ± 0.20 mm. A wear allowance of 3% of the entire tolerance band is applied to the GO side. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage.

 

 

7.                  (USCS units) A sine bar is used to determine the angle of a part feature. The length of the sine bar = 8.000 in. The rolls have a diameter of 1.000 in. All inspection is performed on a surface plate. In order for the sine bar to match the angle of the part, the following gage blocks must be stacked: 2.0000, 0.5000, 0.2500, and 0.0050. Determine the angle of the part feature.

 

 

 

8.                  (SI units) A 150.00 mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size.

 

 

9.                  (SI units) A 125.00 mm sine bar is to be used to inspect the inclination of one of the faces in a part. While the tolerance on the part inclination is +/-0.002 degrees, its nominal value can be anything from 5 to 85 degrees. If the smallest gauge block available is 0.01 mm thick, will this sine bar be of sufficient angular resolution to determine if all possible nominal part inclinations are within tolerance? Hint: Evaluate the resolution for inclination angles from 5 to 85 degrees and plot the resolution as a function of this angle. The plot will give you a visual aid to help you answer the question.

 

  

10.              Convert 0.025 in into mm.

 

 

11.              Convert 25 mm into in.  

 

 

12.              Convert 10.25 degrees into radians; and p, p/2 and p/3 radians into degrees.

 

 

13.              Convert 30.12345 degrees into degrees, minutes and seconds.

 

 

14.              How many degrees are equivalent to one second of arc?

 

 

 

 

 

 

15.              Assume that the surface of a part has a profile given by y = 1.5×10^-6 in sin(2x/in). Both x and y are in inches. Answer the following questions:

 

a.       What is the distance between peaks?

 

 

b.      What is the value of Ra AA over 1 inch length?

 

 

c.       What is the value of Ra RMS over 1 inch length?

 

d.      What process may have produced such surface? Use a chart from the internet or elsewhere to support your answer.

 

 

 

16.              What is the lay in the following surface symbols? Sketch the surfaces. Investigate what machining operations may produce such surface patterns.

 

 

 

 

 

 

 

 

 

 

 

 

17.              Convert 1 μm into thousandths of an inch.

 

 

18.              Convert one ten thousandth of an inch into μm.

 

 

19.              For each of the following process pairs, circle the one that produces a smaller surface roughness. If the processes are about equal, circle both.

 

a)      Sand Casting vs. Polishing

b)      EDM vs. Turning

c)      Rolling vs. Grinding

 

20.              The surface roughness is generally smaller:

 

a)      Across the lay

b)     Along the lay

c)      None of the above

d)     Don’t know, will take the penalty!

Order a unique copy of this paper
(550 words)

Approximate price: $22

Our Basic features
  • Free title page and bibliography
  • Plagiarism-free guarantee
  • Unlimited revisions
  • Money-back guarantee
  • 24/7 support
Our Options
  • Writer’s samples
  • Expert Proofreading
  • Overnight delivery
  • Part-by-part delivery
  • Copies of used sources
Paper format
  • 275 words per page
  • 12 pt Arial/Times New Roman
  • Double line spacing
  • Any citation style (APA, MLA, Chicago/Turabian, Harvard)

AcademicWritingCompany guarantees

Our customer is the center of what we do and thus we offer 100% original essays..
By ordering our essays, you are guaranteed the best quality through our qualified experts.All your information and everything that you do on our website is kept completely confidential.

Money-back guarantee

Academicwritingcompany.com always strives to give you the best of its services. As a custom essay writing service, we are 100% sure of our services. That is why we ensure that our guarantee of money-back stands, always

Read more

Zero-plagiarism tolerance guarantee

The paper that you order at academicwritingcompany.com is 100% original. We ensure that regardless of the position you are, be it with urgent deadlines or hard essays, we give you a paper that is free of plagiarism. We even check our orders with the most advanced anti-plagiarism software in the industry.

Read more

Free-revision guarantee

The Academicwritingcompany.com thrives on excellence and thus we help ensure the Customer’s total satisfaction with the completed Order.To do so, we provide a Free Revision policy as a courtesy service. To receive free revision the Academic writing Company requires that the you provide the request within Fifteen (14) days since the completion date and within a period of thirty (30) days for dissertations and research papers.

Read more

Privacy and Security policy

With Academicwritingcompan.com, your privacy is the most important aspect. First, the academic writing company will never resell your personal information, which include credit cards, to any third party. Not even your lecturer on institution will know that you bought an essay from our academic writing company.

Read more

Adherence to requirements guarantee

The academic writing company writers know that following essay instructions is the most important part of academic writing. The expert writers will, therefore, work extra hard to ensure that they cooperate with all the requirements without fail. We also count on you to help us provide a better academic paper.

Read more

Calculate the price of your order

550 words
We'll send you the first draft for approval by September 11, 2020 at 10:52 AM
Total price:
$26
The price is based on these factors:
Customer Academic level
Number of pages required
Urgency of paper